/********* verändert an eigene Wuensche DL1YAR im Oktober 2020 angepasst an ESP-01 vier einzelne Antenne schaltbar klappt auf dem Steckbrett startet zur Zeit immer mit der vierten Antenne warum ?? *********/ // Load Wi-Fi library #include /* // Replace with your network credentials const char* ssid = "REPLACE_WITH_YOUR_SSID"; const char* password = "REPLACE_WITH_YOUR_PASSWORD"; */ #include"persoenlichNetz.h" // Zeile auskommentieren Netzwerdaten // Set web server port number to 80 WiFiServer server(80); // Variable to store the HTTP request String header; // Auxiliar variables to store the current output state String output0State = "off"; String output1State = "off"; String output2State = "off"; //****** String output3State = "off"; //****** // Assign output variables to GPIO pins const int output0 = 0; const int output1 = 1; const int output2 = 2; const int output3 = 3; // Current time unsigned long currentTime = millis(); // Previous time unsigned long previousTime = 0; // Define timeout time in milliseconds (example: 2000ms = 2s) const long timeoutTime = 2000; void setup() { //Serial.begin(9600); // Initialize the output variables as outputs und LOW setzen pinMode(output0, OUTPUT); pinMode(output1, OUTPUT); pinMode(output2, OUTPUT); pinMode(output3, OUTPUT); digitalWrite(output0, LOW); digitalWrite(output1, LOW); digitalWrite(output2, LOW); digitalWrite(output3, LOW); // Connect to Wi-Fi network with SSID and password //Serial.print("Connecting to "); //Serial.println(ssid); WiFi.begin(ssid, password); while (WiFi.status() != WL_CONNECTED) { delay(500); //Serial.print("."); } // Print local IP address and start web server //Serial.println(""); //Serial.println("WiFi connected."); //Serial.println("IP address: "); //Serial.println(WiFi.localIP()); server.begin(); output0State = "off"; output1State = "off"; //########################### output2State = "off"; //########################### output3State = "off"; //########################### } void loop(){ WiFiClient client = server.available(); // Listen for incoming clients if (client) { // If a new client connects, //Serial.println("New Client."); // print a message out in the serial port String currentLine = ""; // make a String to hold incoming data from the client currentTime = millis(); previousTime = currentTime; while (client.connected() && currentTime - previousTime <= timeoutTime) { // loop while the client's connected currentTime = millis(); if (client.available()) { // if there's bytes to read from the client, char c = client.read(); // read a byte, then //Serial.write(c); // print it out the serial monitor header += c; if (c == '\n') { // if the byte is a newline character // if the current line is blank, you got two newline characters in a row. // that's the end of the client HTTP request, so send a response: if (currentLine.length() == 0) { // HTTP headers always start with a response code (e.g. HTTP/1.1 200 OK) // and a content-type so the client knows what's coming, then a blank line: client.println("HTTP/1.1 200 OK"); client.println("Content-type:text/html"); client.println("Connection: close"); client.println(); // turns the GPIOs on and off if (header.indexOf("GET /0/on") >= 0) { //Serial.println("gpio0 on"); output0State = "on"; output1State = "off"; //########################### output2State = "off"; //########################### output3State = "off"; //########################### digitalWrite(output1, LOW); //########################### digitalWrite(output2, LOW); //########################### digitalWrite(output3, LOW); //########################### digitalWrite(output0, HIGH); } else if (header.indexOf("GET /0/off") >= 0) { //Serial.println("gpio0 off"); output0State = "off"; digitalWrite(output0, LOW); } else if (header.indexOf("GET /1/on") >= 0) { //Serial.println("gpio1 on"); output1State = "on"; output2State = "off"; //########################### output3State = "off"; //########################### output0State = "off"; //########################### digitalWrite(output2, LOW); //########################### digitalWrite(output3, LOW); //########################### digitalWrite(output0, LOW); //########################### digitalWrite(output1, HIGH); } else if (header.indexOf("GET /1/off") >= 0) { //Serial.println("gpio1 off"); output1State = "off"; digitalWrite(output1, LOW); } else if (header.indexOf("GET /2/on") >= 0) { //Serial.println("gpio2 on"); output2State = "on"; output3State = "off"; //########################### output0State = "off"; //########################### output1State = "off"; //########################### digitalWrite(output3, LOW); //########################### digitalWrite(output0, LOW); //########################### digitalWrite(output1, LOW); //########################### digitalWrite(output2, HIGH); } else if (header.indexOf("GET /2/off") >= 0) { //Serial.println("gpio2 off"); output2State = "off"; digitalWrite(output2, LOW); } else if (header.indexOf("GET /3/on") >= 0) { //Serial.println("gpio3 on"); output3State = "on"; output0State = "off"; //########################### output1State = "off"; //########################### output2State = "off"; //########################### digitalWrite(output2, LOW); //########################### digitalWrite(output0, LOW); //########################### digitalWrite(output1, LOW); //########################### digitalWrite(output3, HIGH); } else if (header.indexOf("GET /3/off") >= 0) { //Serial.println("gpio3 off"); output3State = "off"; digitalWrite(output3, LOW); } // Display the HTML web page client.println(""); // client.println("\n"); //########################### client.println(""); client.println(""); // CSS to style the on/off buttons // Feel free to change the background-color and font-size attributes to fit your preferences client.println(""); //rot **** // Web Page Heading client.println("

DL1YAR Antennen

"); // Display current state, and ON/OFF buttons for gpio0 //client.println("

gpio0 - State " + output0State + "

"); client.println("

gpio0 - DIPOL " + output0State + "

"); // If the output0State is off, it displays the ON button if (output0State=="off") { //########################### //if (output0State=="on") { client.println("

"); } else { client.println("

"); } // Display current state, and ON/OFF buttons for gpio1 //client.println("

gpio1 - State " + output1State + "

"); client.println("

gpio1 - GP-ant " + output1State + "

"); // If the output1State is off, it displays the ON button if (output1State=="off") { //########################### // if (output1State=="on") { client.println("

"); } else { client.println("

"); } client.println("

gpio2 - Ant3 " + output2State + "

"); // If the output2State is off, it displays the ON button if (output2State=="off") { //########################### // if (output2State=="on") { client.println("

"); } else { client.println("

"); } client.println("

gpio3 - AntX " + output3State + "

"); // If the output2State is off, it displays the ON button if (output3State=="off") { //########################### // if (output2State=="on") { client.println("

"); } else { client.println("

"); } client.println(""); // The HTTP response ends with another blank line client.println(); // Break out of the while loop break; } else { // if you got a newline, then clear currentLine currentLine = ""; } } else if (c != '\r') { // if you got anything else but a carriage return character, currentLine += c; // add it to the end of the currentLine } } } // Clear the header variable header = ""; // Close the connection client.stop(); //Serial.println("Client disconnected."); //Serial.println(""); } }